ziselierte Silberschmiedearbeit
Salisches Taufbecken um 1129:
reife Tollkirschen
Zerstörung
es gibt immer was zu tun...
Kolbenente
der Dr-Willke-Weg
Tor zum ehem. Zisterzienserkloster Braunschweig Ri…
Renaissancetür
St. Marie zu Riddagshausen
Eva und Apfel
ehem. Zisterzienser Klosterkirche Riddagshausen
Konsole an der Vierung
Rippengewölbe
Riddagshausen
Gemüse und Heilpflanzen
Gans
Graugänse auf der Klosterwiese
Geburtshaus Seerose und Teestube IsTeetied
im Klostergarten
Balsamkraut / Tanacetum balsamita
Liebstöckel - auch Maggiekraut genannt
Echter Baldrian
Blick von der Königszinne auf Bodenwerder
gemauerte Stützen für den Balkon
ein Bauernhof
altes Ziegeldach von unten
von der Rolle
besonderer Wetterschutz
ein Plausch während der Mittagspause
der neue Laptop in der Fußgängerzone
Bärlauch
im Hof des Welfenschlosses Herzberg
Herzog Christian Ludwig 1641-65
Turmuhr am Schloß Herzberg
er wacht an der Turmecke des Schlosses
Detail
Säulen /...
Am Eckturm im Schloß
kupferne Wasserspeier etwa um 1640
Detai einer Türlaibung am Südflügel
Türendetail
Türklopfer
Wappen am Westflügel
Schloß Herzberg Westtrakt:
See also...
Keywords
Authorizations, license
-
Visible by: Everyone -
All rights reserved
-
1 036 visits
Armbanduhrwerk - diverses


Ipernity schneidet nach 128 Zeichen die Notizen ab. Interessierte Leser mögen sich also mit dem teilweise längeren Text in Englisch den kompletten Inhalt suchen.
----
1.) Oscillating Quartz create the time-normal : usually with 32.7 kilo Hz.
2.)The electronics board contains an integrated circuit, an adjustable capacity to trim to the frequency of the Quartz. Two electrical Output power to amplifiers the positive and negative signal coming out of IC
3.) Printed circuid board with transitional body to induction coil on the stator of the motor of this wristwatch-clock.
4.) coil for the generation of electromagnetic fluxes.
This part is assembled on the metal part shown aside. Both parts form the stator of the motor of the wristwatch. The coil is made of thin insulated copper wire and has 400 to 800 coils. This is once in the direction of A and after the rotor has an accomplished a halve turn electrical charge flows in the opposite B direction.
5.) Metal part, magnetically conductive. In this section runs in the middle hole of the rotor of which the first gear is one of the clock (this magnetic rack part is not shown here). The other holes left and right of them are adjusting the parts and to adjust the magnetic flow in the motor.
6.)Gearwheels for wrist-watches come either from Switzerland or from Japan and here like there other standards are considered to the gear cutting.
7.)steel lap lever and plastic insulator for the watch battery
8.) Model from metal for testing of the mechanical funcitins of the winding button of the watch also for example, of progress the set other of the day (the white die casted ring with 1-31)
10.)the clockface is plugged on the clockwork. Then the pointers are mounted
11.)Feather bar for the attachment of the watch-strap
30.)Anchor inhibition of a mechanical alarm clock (does not belong here) :-)
Translate into English
----
1.) Oscillating Quartz create the time-normal : usually with 32.7 kilo Hz.
2.)The electronics board contains an integrated circuit, an adjustable capacity to trim to the frequency of the Quartz. Two electrical Output power to amplifiers the positive and negative signal coming out of IC
3.) Printed circuid board with transitional body to induction coil on the stator of the motor of this wristwatch-clock.
4.) coil for the generation of electromagnetic fluxes.
This part is assembled on the metal part shown aside. Both parts form the stator of the motor of the wristwatch. The coil is made of thin insulated copper wire and has 400 to 800 coils. This is once in the direction of A and after the rotor has an accomplished a halve turn electrical charge flows in the opposite B direction.
5.) Metal part, magnetically conductive. In this section runs in the middle hole of the rotor of which the first gear is one of the clock (this magnetic rack part is not shown here). The other holes left and right of them are adjusting the parts and to adjust the magnetic flow in the motor.
6.)Gearwheels for wrist-watches come either from Switzerland or from Japan and here like there other standards are considered to the gear cutting.
7.)steel lap lever and plastic insulator for the watch battery
8.) Model from metal for testing of the mechanical funcitins of the winding button of the watch also for example, of progress the set other of the day (the white die casted ring with 1-31)
10.)the clockface is plugged on the clockwork. Then the pointers are mounted
11.)Feather bar for the attachment of the watch-strap
30.)Anchor inhibition of a mechanical alarm clock (does not belong here) :-)
Gabi Lombardo, aNNa schramm have particularly liked this photo
- Keyboard shortcuts:
Jump to top
RSS feed- Latest comments - Subscribe to the comment feeds of this photo
- ipernity © 2007-2025
- Help & Contact
|
Club news
|
About ipernity
|
History |
ipernity Club & Prices |
Guide of good conduct
Donate | Group guidelines | Privacy policy | Terms of use | Statutes | In memoria -
Facebook
Twitter
Ulrich Dinges club has replied to Adam * clubUlrich Dinges club has replied to aNNa schramm clubUlrich Dinges club has replied to Gabi Lombardo clubDie Uhren mit digitaler Anzeige sind einfacher,
Danke Gabi für den Besuch meines Albums
Sign-in to write a comment.